chesters1 1546 Posted January 4, 2008 Share Posted January 4, 2008 (edited) on boot up today i had a blue screen and no disk use light (not the usual cant find the boot bit) ,i fixed the problem with the fixboot utility in the windows disk then ran chkdsk on a second boot from the CD. booted fine from HD after that but on running the disk checking facility in windows on rebooting and it starting i get a report : Unable to read Usn journal $] Data stream (or words to that effect) it then abandons the rest of the error checking and boots into windows as normal how do i get the poor thing to read that Data stream so i can fully check the disk? ps if you run the disk check function within windows it goes through 2 sequences then up pops an error box with unable to complete disk check (or words to that effect) pps can some kind person remind me of what i write into the run box on the start panel that persuades windows to check its files are ok? (not sfc) another strange problem is system restore doesent work on the last two saves! goes through the motions but ends up saying its sorry but it cant ,no viruses nor bots nor nothing naughty found on disk! Edited January 4, 2008 by chesters1 Believe NOTHING anyones says or writes unless you witness it yourself and even then your eyes can deceive you There is only one opinion i listen to ,its mine and its ALWAYS right even when its wrong Its far easier to curse the darkness than light one candle Mathew 4:19 Grangers law : anything i say will turn out the opposite or not happen at all! "To compel a man to furnish contributions of money for the propagation of opinions which he disbelieves and abhors, is sinful and tyrannical." Thomas Jefferson Link to post Share on other sites
IanR 0 Posted January 4, 2008 Share Posted January 4, 2008 Hi Are you running Windoze 2000, or XP under NTFS? Cheers Ian. http://www.robertianrae.co.uk/ http://www.caravanorkney.co.uk/ Link to post Share on other sites
chesters1 1546 Posted January 4, 2008 Author Share Posted January 4, 2008 (edited) xp and ntfs ,everything seems fine but for the problems above Edited January 4, 2008 by chesters1 Believe NOTHING anyones says or writes unless you witness it yourself and even then your eyes can deceive you There is only one opinion i listen to ,its mine and its ALWAYS right even when its wrong Its far easier to curse the darkness than light one candle Mathew 4:19 Grangers law : anything i say will turn out the opposite or not happen at all! "To compel a man to furnish contributions of money for the propagation of opinions which he disbelieves and abhors, is sinful and tyrannical." Thomas Jefferson Link to post Share on other sites
IanR 0 Posted January 4, 2008 Share Posted January 4, 2008 Try: Firing up in safe mode (F8, usually) (as administrator). Go to START>RUN. Type in "CMD" (without the quotes). At the > Command Prompt, type in "CHKntfs /X C:" (without the quotes). Hit ENTER. Then type "Exit" (without the quotes). Reboot. Cheers Ian. http://www.robertianrae.co.uk/ http://www.caravanorkney.co.uk/ Link to post Share on other sites
chesters1 1546 Posted January 4, 2008 Author Share Posted January 4, 2008 (edited) it just says "the type of file system is NTFS" ! and on rebooting it merely reboots? Edited January 4, 2008 by chesters1 Believe NOTHING anyones says or writes unless you witness it yourself and even then your eyes can deceive you There is only one opinion i listen to ,its mine and its ALWAYS right even when its wrong Its far easier to curse the darkness than light one candle Mathew 4:19 Grangers law : anything i say will turn out the opposite or not happen at all! "To compel a man to furnish contributions of money for the propagation of opinions which he disbelieves and abhors, is sinful and tyrannical." Thomas Jefferson Link to post Share on other sites
IanR 0 Posted January 4, 2008 Share Posted January 4, 2008 OK. Can you download and run your hard drive manufacturers diagnostic utility? Cheers Ian. http://www.robertianrae.co.uk/ http://www.caravanorkney.co.uk/ Link to post Share on other sites
peterpikefisher 12 Posted January 5, 2008 Share Posted January 5, 2008 (edited) 1. Click Start, and then Run. 2. In Open, type cmd, and then press ENTER. 3. Use one of the following procedures: • To run Chkdsk in read-only mode, at the command prompt, type chkdsk and then press ENTER. • To repair errors without scanning the volume for bad sectors, at the command prompt, type chkdsk f Dont Forget About The Space Between chkdsk and f and then press ENTER. Note If one or more of the files on the hard disk are open, you will receive the following message: Chkdsk cannot run because the volume is in use by another process. Would you like to schedule this volume to be checked the next time the system restarts? (Y/N) Type Y, and then press ENTER to schedule the disk check, and then type exit restart your computer to start the disk check. To repair errors, locate bad sectors, and recover readable information, at the command prompt, type chkdsk r Dont Forget About The Space Between chkdsk and r and then press ENTER. Note If one or more of the files on the hard disk are open, you will receive the following message: Chkdsk cannot run because the volume is in use by another process. Would you like to schedule this volume to be checked the next time the system restarts? (Y/N) Type Y, and then press ENTER to schedule the disk check, and then type exit restart your computer to start the disk check. good luck regards pete Edited January 5, 2008 by pumphypete 15/06/12 PB Perch 3 lb 10 oz 03/03/11 Common Carp 23lb 6 oz 05/06/12 Sturgeon 7 lb 13 oz 06/06/12 Mirror Carp 21 lb 2 oz 09/03/13 PB PIKE 27 lb 9 oz Link to post Share on other sites
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now